r2 d2 3D 프린트 모델

line width: 0.4 mm support
floor line width: 0.4
initial layer
line width: 100%
shell wall thickness: 0.8 mm
wall line count: 2 outer wall wipe distance: 0.2 mm top surface skin layers: 0 top/bottom thickness: 0.8 mm top thickness: 0.8 mm top layers: 8 bottom thickness: 0.8 mm bottom layers: 8 top/bottom pattern: lines bottom pattern initial layer: lines top/bottom line directions: [ ] outer wall inset: 0 mm compensate wall overlaps: check compensate outer wall overlaps: check compensate inner wall overlaps: check fill gaps between walls: everywhere horizontal expansion: 0 mm initial layer horizontal expansion: 0 mm z seam alignment: sharpest corner ignore small z gaps: check extra skin wall count: 1 infill infill density: 20% (all parts of the connectors should be printed at 100% infill) infill line distance: 4.0 mm infill pattern: grid infill line directions: [ ] infill overlap percentage: 10% infill overlap: 0.04 mm skin overlap percentage: 5% skin overlap: 0.02 mm infill wipe distance: 0.1 mm infill layer thickness: 0.1 mm gradual infill steps: 0 infill before walls: check minimum infill area: 0 mm2 skin expand distance: 0.8 top skin expand distance: 0.8 bottom skin expand distance: 0.8 maximum skin angle for expansion: 90° minimum skin width for expansion: 0.0 material enable retraction: check retraction extra prime amount: 0 mm3 retraction minimum travel: 0.8 mm maximum retraction count: 90 minimum extrusion distance window: 6.5 mm nozzle switch retraction distance: 16 mm nozzle switch retraction speed: 20 mm/s nozzle switch retract speed: 20 mm/s nozzle switch prime speed: 20 mm/s speed print speed: 45 mm/s infill speed: 50 mm/s wall speed: 22.5 mm/s outer wall speed: 22.5 mm/s inner wall speed: 45 mm/s top/bottom speed: 15 mm/s support speed: 45 mm/s support infill speed: 45 mm/s support interface speed: 30 mm/s support roof speed: 30mm/s support floor speed: 30 mm/s travel speed: 80 mm/s initial layer speed: 15 mm/s initial layer print speed: 15 mm/s initial layer travel speed: 26.6667 mm/s skirt/brim speed: 15 mm/s maximum z speed: 0 mm/s number of slower layers: 2 travel combing mode: all avoid printed parts when traveling: check travel avoid distance: 0.625 mm cooling enable print cooling: check fan speed: 100% regular fan speed: 100% maximum fan speed: 100% regular/maximum fan speed threshold: 10 s initial fan speed: 0% regular fan speed at height: 0.3 mm regular fan speed at layer: 2 minimum layer time: 5 s minimum speed: 10 mm/s support enable support: check support placement: everywhere support overhang angle: 60° support pattern: zig zag connect support zigzags: check support density: 15 % support line distance: 1.3333 mm support z distance: 0.3 mm support top distance: 0.3 mm support bottom distance: 0.3 mm support x/y distance: 0.7 mm support distance priority: z overrides x/y minimum support x/y distance: 0.2 mm support stair step height: 0.3 mm support stair step maximum width: 5.0 mm support join distance: 2.0 mm support horizontal expansion: 0.2 mm support infill layer thickness: 0.1 mm use towers: check tower diameter: 3.0 mm minimum diameter: 3.0 mm tower roof angle: 65° build plate adhesion build plate adhesion type: brim skirt/brim minimum length: 250 mm brim width: 8.0 mm brim line count: 18 brim only on outside: check mesh fixes union overlapping volumes: check merged meshes overlap: 0.15 mm special modes print sequence: all at once surface mode: normal spiralize outer contour: check (only for balls 40-45 files) disclaimer: this model will look outstanding if printed on sla/sls 3d printer. the accuracy of the model printed on fff printer can vary from the result shown in the pictures.

thanks for purchasing! 프린트 준비: 아니오